Free shipping on orders over ₪600 · Stock in Israel · Bit, bank transfer or card by phone

How to Choose an FPV Frame: Size, Layout, Carbon and Mounts

Published 5 November 2026

The frame decides which propellers, motors, stack and battery you can use, so it is the first part to settle. Start from the propeller size and the kind of flying, then check the mounting dimensions before you buy.

Start with the propeller size

Frames are sold by the largest propeller they take. Everything else in the build follows from that choice. These are the usual uses:

  • 5 inch: freestyle and racing, the most common size, with the widest choice of parts. 6 inch frames exist for a little more efficiency.
  • 7 inch: long range and efficient cruising, usually with a larger battery, often Li-ion.
  • 10 inch: long range with a camera or a small payload, and slow, smooth cinematic flying.
  • 13 inch and up: heavy lift, large cinema cameras and cargo. These are closer to small aircraft than to toys, so treat the electronics and the battery as safety items.
  • X-class: very large, high-power builds. The term comes from the community and from events rather than from one fixed standard, so check what a given frame is actually designed for.

Wheelbase and propeller clearance

Wheelbase is the distance between diagonally opposite motor centres, in millimetres. It is a rough guide to size, but the number that matters is the room for propellers. On a square layout, two neighbouring motors are about 0.7 times the wheelbase apart, and the two propellers must not touch. Leave a gap of at least a few millimetres, because arms flex and propellers bend in a crash.

A worked example: a 5 inch propeller is about 127 mm across, and on a frame with a 220 mm wheelbase neighbouring motors are roughly 155 mm apart, which leaves room. The same arithmetic shows why a propeller that is one size too large for a frame cannot simply be bolted on.

Use the maximum propeller size the manufacturer lists for the frame. Going one size up is sometimes possible on a long-armed layout, but the propellers then sit very close and the frame needs to be stiff.

Arm thickness and carbon quality

Arms take most of the crash damage, so thickness matters. On a 5 inch frame, around 4 mm is common for freestyle, and thinner arms save weight on racing builds. Thicker arms, 5 to 6 mm, add durability at a cost in weight, and larger frames usually go thicker still, because longer arms put more leverage on the joint.

In a listing, 3K refers to the weave: each bundle of fibres in the cloth holds 3,000 filaments. It describes the look of the surface, a woven pattern, and not the strength of the whole plate. T700 and similar names are grades of the raw carbon fibre.

Neither label tells you how good the finished plate is. That depends on the resin, the number and orientation of the layers, how cleanly the plate is cut and whether the edges are sealed. A plain description of the plate, with its thickness stated, is more useful than a fibre grade. If you are unsure, read reviews that show crash damage.

Stiffness matters as well as strength. Arms and plates that flex under load can feed vibration into the gyro and make tuning harder, so a rigid, well-braced design is worth more than a thin one that merely saves a few grams.

True-X, stretched-X, H and deadcat

True-X has all four motors at the corners of a square. It is symmetrical, so pitch and roll feel the same and the drone is easy to tune. The front props can show at the edges of a wide camera view.

Stretched-X makes the front-to-back distance longer than the left-to-right distance. The drone feels steadier in pitch, with a little less snap, and the front props sit further from the camera. Many freestyle frames use it. A different layout changes how the drone flies, so you may want to adjust your tune afterwards.

H and deadcat layouts push or sweep the front arms outward so the front props stay out of the picture. They suit cinematic and long-range flying with a wide-angle camera, and they usually trade some agility for a clean view.

Unibody or bolt-together arms, and spare parts

A unibody frame has arms cut from one bottom plate. It has fewer parts and fewer joints that can loosen, but a broken arm usually means replacing the whole plate. Bolt-together frames use separate arms held with screws. They have more joints to keep tight, but a broken arm is a cheap, quick swap.

Whichever you choose, check before you buy that spare arms or plates are sold separately and are likely to stay on offer, and keep one spare set. A frame whose arms you cannot replace is a risk for any build that will crash.

Mounting: stack, motors, camera and battery

Many numbers on the frame page are fixed patterns, and each one has to match the part that goes in it.

Stack mount: flight controller and ESC boards come in 30.5 x 30.5, 20 x 20 and 16 x 16 mm hole patterns. Match the pattern to your boards. Also check the standoff height against the stack, since an ESC and flight controller plus a VTX or an HD unit can be taller than a frame allows.

Motor mount: the pattern, for example 16 x 16, 19 x 19 or 25 x 25 mm, depends on the motor's size and differs between models, so read the motor's specification and compare it with the frame's arm drilling. Motor screw length also has to suit the arm thickness.

Camera and VTX: camera cages come in different widths. Compare your camera's width in millimetres with the frame's slot, and check whether an HD air unit and the antenna have somewhere to go. A top plate with a GoPro-style mount is useful only if you plan to carry an action camera.

Battery: measure length, width and height of the pack you intend to fly, then compare with the strap width and the tray length. Large Li-ion packs are noticeably bigger and heavier than the LiPo packs a 5 inch frame is drawn around. Check the strap path and that the weight sits close to the middle of the drone.

A bigger frame changes the rest of the build

Bigger propellers need lower-KV motors with larger stators, and usually a bigger battery to match. The guides on choosing motors and on flight time cover those choices. Weight also grows with size, so compare the frame's weight against its strength rather than chasing the lightest one.

A heavier frame that survives crashes usually costs less over time than a light one that cracks. Also remember that every part you add on top of the frame, a camera, a GPS mast or a bigger battery, raises the take-off weight, and the frame has to carry it without flexing.

Four numbers to check before you buy

  • Maximum propeller size the frame is listed for, against your propellers
  • Motor mounting pattern against the motors you picked
  • Stack pattern and the standoff height available, against the boards in your stack
  • Battery length, width and height against the tray and strap
  • Also confirm the camera width and that replacement arms are available

Shop the parts

More guides

Related products

FFPV.BASE

An Israeli shop for FPV drone parts and ready-to-fly quads. Build, fly, upgrade — all in one place.

Israeli FPV storeLicensed dealer no. 060875804Licensed by the Israeli Ministry of Communications to trade in wireless equipment
Categories
Customer service
Contact
© 2026 FPV.BASE — All rights reserved