FPV Battery Connectors: XT30, XT60, XT90 or QS8?
The battery connector carries every amp your drone uses, so it has to suit the current, the wire and the size of the build. This guide compares the common connectors, explains which half goes on the battery and which on the drone, and covers soldering and anti-spark connectors.
How to read a connector's current rating
Manufacturers rate a connector at a specific wire gauge and a specific temperature rise. Amass, for example, rates the XT60 at 35A maximum with 12AWG wire and a temperature rise of no more than 85K. Change the wire or the conditions and the real limit changes with them.
Peak current can go above the rating for short bursts, such as a hard punch-out, without harm. Continuous current, the current the drone draws through most of the flight, should stay within the rating. A connector run above its rating for long periods heats up, its resistance rises and its contacts wear.
XT30, XT60, XT90 and QS8 at a glance
These figures come from the manufacturers' own product pages.
Amass XT connectors have a PA (nylon) housing and gold-plated brass contacts. The XT30U and XT60 are rated UL94 V-0, with an operating range of -20 to 120 °C.
- XT30 (Amass XT30U): up to 20A with 16AWG wire, 80V DC rated voltage. Suits small drones: toothpicks, cinewhoops and 2 to 3 inch builds.
- XT60 (Amass): up to 35A with 12AWG wire. The most common connector on 3 to 7 inch FPV drones. The XT60H is the same connector with a rear sheath that covers the solder joints.
- XT90 (Amass): up to 45A with 10AWG wire. A larger connector for builds whose continuous current goes beyond the XT60's rating. The XT90-S version is an anti-spark connector.
- QS8 (QIUSHANG QS8-S): 8 mm gold-plated brass contacts, rated 110 to 180A, for 8 to 12AWG wire, with a built-in anti-spark resistor. Found on large batteries: heavy-lift, agricultural and long-range drones.
Match the connector to your build's current
Start from the current the build actually draws. The motor manufacturer's thrust table shows the current on your propeller and voltage, and multiplied by four it gives a rough figure for the whole drone at full throttle. For the connector, what matters most is the current you hold for long stretches, not the momentary peak.
If your continuous current sits close to a connector's rating, go up a size. A larger connector adds a few grams and runs cooler; a connector working at its limit heats up flight after flight.
Keep it in proportion. An XT90 on a 3 inch drone adds weight for no benefit, and an XT30 on a 7 inch long-range build is likely to be pushed past its rating.
Use the same connector on the battery and the drone. An adapter between connector types adds contact resistance and one more joint that can work loose, so keep adapters for charging and the bench, not for flight.
Male or female: which half goes on the battery
The usual convention is that the power source carries the female half, the one with sockets, and the drone carries the male half, the one with pins. A battery is always live, so its contacts sit recessed inside the housing where a finger, a tool or a stray piece of metal cannot short them. The drone's exposed pins only become live once a battery is plugged in.
With XT30, XT60 and XT90 this normally means a female connector on the battery and a male one on the drone's power lead. Whatever you choose, stay consistent across your whole fleet, so every battery fits every drone and charger and nothing exposed is ever live.
QIUSHANG's QS8 naming can be misleading: the male is the wide housing with the pins inside it, and the female is the narrow housing with sockets. When ordering QS8, go by the photo and by the half already on your battery, not only by the word male or female.
Soldering a connector
The wire matters as much as the connector. The ratings above were measured with a specific gauge: 16AWG for XT30, 12AWG for XT60, 10AWG for XT90 and 8 to 12AWG for QS8. If your current approaches the rating, use at least that gauge, or the wire will heat up before the connector does. Remember that a smaller AWG number means a thicker wire.
Slide heat-shrink onto each wire before you solder, tin both the wire and the connector's solder cup, then join them with enough heat for the solder to flow into the joint rather than sit on top of it. Shrink the sleeve so it covers the whole joint with no bare metal showing. On an XT60H the rear sheath does part of that job.
Check polarity twice: red to positive, black to negative, following the marking on the housing and the half it will mate with. The connectors only fit together one way, so a mistake at the soldering stage carries reversed polarity straight into the ESC.
When replacing the connector on a battery, cut and solder one lead at a time so the two bare ends can never touch. Never solder on a drone with a battery connected.
Anti-spark connectors and why large builds need them
An ESC has capacitors on its input. The moment you plug in a battery they charge almost instantly, a short burst of current jumps across the contacts as they meet, and you hear a snap and may see a spark. Each spark burns away a little of the contact surface, and over time the contacts pit and their resistance rises.
On a small drone the spark is minor. On large builds, with higher voltage and bigger input capacitors, it becomes a real problem, which is why connectors for big batteries have an anti-spark design. In the QS8-S a built-in resistor makes contact first and pre-charges the ESC capacitors, and only then do the main contacts close, so there is no spark and no wear. QIUSHANG uses a 5.1 ohm resistor for devices under 60V and offers a 15 ohm version for devices over 60V.
For builds that use XT90, Amass makes the XT90-S, an XT90 with an anti-spark design. With any anti-spark connector, push the two halves fully home so the main contacts close completely.
Safety checklist
Before the first flight on a new lead or battery:
- Continuous current is within the connector's rating, at the wire gauge it was rated with
- Battery and drone use the same connector, with the female half on the battery side across the fleet
- Every joint is covered in heat-shrink with no bare metal showing
- Polarity has been checked before the first battery goes in
- Large, high-voltage builds use an anti-spark connector
- A connector that is discoloured, loose or hot after a flight gets replaced, not ignored
- The battery is unplugged straight after landing and before any work on the drone



