Free shipping on orders over ₪600 · Stock in Israel · Bit, bank transfer or card by phone

Adding ExpressLRS to Your Radio with an External Module

Published 5 November 2026

If your radio does not have ExpressLRS built in, you can still fly ELRS by plugging an external transmitter module into the radio's module bay. The one thing to get right before buying is that the module and the bay match, so this guide starts with how to check that, then covers power, antennas, settings and testing.

What does an external ELRS module do?

The radio still reads your sticks and switches and applies your mixes. It then sends the resulting channel data through the module bay to the module over a serial link, usually the CRSF protocol. The module turns that data into ExpressLRS radio packets and transmits them to the receiver on the drone. Telemetry such as battery voltage and link quality travels back the same way, and the module hands it to the radio.

That is why there are two things to check: the radio must be able to output that serial link on its bay, and the module must be built for that bay. A module can usually move to another radio with the same bay type.

How do I check my radio's bay?

Bay formats and their names vary between manufacturers, so do not guess from the radio's size. Look in the radio's manual or specification page for the external module bay, and compare it with the bay type listed on the module's page. The module's connector and physical size must match the bay. If they do not, do not force it.

These are the formats you will meet most often:

  • JR-style bay: the larger bay on the back of full-size radios. It takes full-size modules.
  • Micro bay: a smaller bay on some compact radios. It takes Micro-size modules.
  • Nano bay: a smaller bay still, on some compact radios. It takes Nano-size modules.
  • No bay: some radios have no external bay at all, and for those ELRS has to be built in.
  • Radio firmware: on EdgeTX and OpenTX radios the external module is set to CRSF in the model settings, and older firmware versions may not offer it. ETHOS radios work differently, so check the radio's manual rather than assuming the same menus.

Power, output power and local rules

On many radios the bay supplies power to the module from the radio's battery. Lower-output modules usually run happily from that. Higher-output modules draw more current while transmitting, and some can also take external power through a separate connector. Check both the module's manual and the radio's manual for the current the bay can supply and the voltage range the module accepts, and start a session with a charged radio battery, because a sagging supply can cause the module to reset or drop out.

Modules differ in their maximum RF output power, and a higher maximum is not something to run all the time. More power raises the range at a given packet rate, but it also adds heat and drains the radio's battery faster. Rules on transmit power differ by region, so check what is legal where you fly. Some regional firmware builds, such as those using listen-before-talk (LBT), limit power. ExpressLRS also has a dynamic power option, where the module lowers its power when the link is strong, which relies on telemetry.

For the choice between 2.4 GHz and 868/915 MHz, see our guide on ELRS 868/915 MHz vs 2.4 GHz.

Antennas: type and direction

Use an antenna made for your module's band and with the right connector. Never transmit without an antenna attached, because a transmitter running into nothing can be damaged.

A T-antenna or a dipole is omnidirectional in the horizontal plane, but it is weakest along its own axis. Do not point the tip at the drone. Hold the antenna upright and tilt it so its side faces the aircraft, especially when the drone is far away or high.

A Moxon is more directional. It can add range in one direction, but you have to keep its face aimed at the drone. Keep the antenna clear of your hand and body, and check that nothing metal sits right next to it.

Packet rate, telemetry ratio and the Lua script

Packet rate is how many control packets per second the module sends. At 50 Hz a new packet goes out every 20 ms, and at 500 Hz every 2 ms. A higher rate means lower latency, so the drone reacts to the sticks sooner, but each packet is sent with less margin and the range is shorter. A lower rate gives longer range at the cost of latency. As a rule of thumb, use higher rates for freestyle and racing, and lower rates for long range. The rates on offer depend on the band, the hardware and the ELRS version.

The telemetry ratio sets how many packets are reserved for data coming back from the drone. More telemetry gives fresher data but leaves less airtime for control.

On EdgeTX and OpenTX you change these settings from the ExpressLRS Lua script. Copy the script to the radio's SD card, in the scripts tools folder, and run it from the tools menu. It shows the packet rate, telemetry ratio and transmit power, plus options for binding and starting WiFi. Which options appear depends on the module and its firmware version. The radio's baud rate for the external module should follow the module's documentation, as a low baud rate can limit the highest packet rates. On ETHOS radios, check the radio's manual for how to reach the same settings.

Receiver, bind phrase and firmware updates

The receiver and the module must use the same band, and their ExpressLRS versions must be compatible. Keep both on the same major version, for example 3.x with 3.x. They also need the same bind phrase, and when both are set correctly the receiver connects without a separate bind step. Our receivers category lists ELRS receivers by band.

To update the module, use the ExpressLRS Configurator or the radio's Lua script to put it into WiFi update mode, or use the other methods that the module supports, such as Bluetooth or USB on some models. Pick the firmware target that matches your exact module, and read its manual first. After a major version change, update the receivers too.

How do I bind and test the range?

Do a range test before the first real flight, and again after any change of antenna, power or settings:

  • Make sure the module and receiver run compatible versions and share the same bind phrase, then power both and confirm the link in the Lua script or on the radio's telemetry screen.
  • Take the propellers off, or keep the drone on the bench, then set the transmit power to the lowest setting your module offers.
  • Walk away with the radio, holding the antenna the way you will fly, while watching link quality and RSSI on the radio or in the OSD.
  • Note the distance where the link starts to degrade, and check that the failsafe behaves as you set it up.
  • Set the power back to your normal level and confirm that the link quality improves.

Checklist before you buy

  • Which bay does the radio have, JR-style, Micro or Nano, and does the module list the same one?
  • Does the radio's firmware support external CRSF output?
  • Is the module's band the same as your receivers', 2.4 GHz or sub-GHz, or is it dual-band?
  • Can the bay supply the module's current, or does the module offer external power?
  • What is the module's maximum output power, and is it allowed where you fly?
  • Is the antenna included, and does its band and connector fit?
  • Are your receivers on ELRS versions compatible with the module?

Shop the parts

More guides

Related products

FFPV.BASE

An Israeli shop for FPV drone parts and ready-to-fly quads. Build, fly, upgrade — all in one place.

Israeli FPV storeLicensed dealer no. 060875804Licensed by the Israeli Ministry of Communications to trade in wireless equipment
Categories
Customer service
Contact
© 2026 FPV.BASE — All rights reserved