How to Choose an FPV Radio: Protocol, Firmware, Gimbals
The radio is the part of an FPV kit you keep the longest, and it usually serves several drones. Before comparing screens and switches, make sure it speaks the same language as your receiver. This guide goes through the protocol, the operating system, the RF module, the gimbals and the size of the radio, in that order.
Start with the receiver: the protocol must match
A radio only controls a drone whose receiver uses the same control link. In FPV that means choosing an ecosystem first:
If you already own drones, check which receivers they carry before you buy a radio. If you are starting from scratch, the radio's protocol decides which receivers you will buy from now on.
- ExpressLRS: an open-source control link, with receivers from several manufacturers. A radio with built-in ExpressLRS flies drones that have an ExpressLRS receiver.
- FrSky: FrSky's own protocols, such as ACCST D16, ACCESS and TW. These need FrSky-compatible receivers.
- DJI: the DJI FPV Remote Controller 3 is made for DJI O4 video transmission and pairs only with DJI drones and air units: Avata 2, Avata 360, Neo, Neo 2, O4 Air Unit, O4 Air Unit Pro, O4 Wide and O3 Air Unit. It does not control a drone with an ExpressLRS or FrSky receiver.
Built-in RF or an external module bay
Many radios have a built-in RF module for one protocol and a bay at the back for an external module. The built-in module sets what the radio does out of the box; the bay lets you add another protocol later without replacing the radio.
Two examples: the RadioMaster TX15 has built-in ExpressLRS on an LR1121 chip covering both 2.4GHz and 900MHz, a JR-compatible module bay, and is also compatible with mLRS. The FrSky TWIN X14 has an internal TW-ISRM module that transmits on two 2.4GHz bands at once in TW mode and supports ACCST D16, ACCESS and TW. It has no internal ExpressLRS, but it does have a Lite-size external module bay.
Check the bay size against the module you have in mind. A JR-size module does not fit a Lite bay, or the other way round, without an adapter.
EdgeTX or ETHOS
EdgeTX is an open-source operating system for radios, and RadioMaster is one of the manufacturers that uses it, for example on the TX15. Model setup, mixes and Lua scripts work the same way on any EdgeTX radio, and ExpressLRS settings are changed from the radio through the ExpressLRS Lua script.
ETHOS is FrSky's own operating system, found on FrSky radios such as the TWIN X14. It is built around FrSky's hardware and protocols.
Neither is better in itself. The choice follows the ecosystem: an ExpressLRS radio running EdgeTX, like the TX15, or a FrSky radio running ETHOS, like the X14. It is worth looking at the menus and screen before you buy, because you will spend a fair amount of time setting up models on it.
2.4GHz or 900MHz
2.4GHz gives high packet rates and small antennas, which suits freestyle and racing, where low latency matters and the range needed is modest.
900MHz (sub-GHz) penetrates obstacles better and is popular for long-range flying, with larger antennas. A radio with a dual-band module, such as the LR1121 in the TX15, can use either band, but the receiver on the drone must support the band you transmit on.
In Israel, according to the Ministry of Communications, drones are approved for use only in the 2400-2483.5 MHz and 5725-5875 MHz bands, and drones that operate in the 900 MHz band are not approved. For flying in Israel, choose a 2.4 GHz control link, and check the frequency specification of the radio and the receiver before you buy.
Gimbals: why hall sensors
The gimbals are the sticks and the mechanism that measures their position. Hall-sensor gimbals measure position with a magnet and a sensor that never touch, so there is no track to wear and the reading stays smooth over time. The TX15 has V5.0 hall-sensor gimbals, and the TWIN X14 uses hall-sensor gimbals too.
Also check whether the stick tension and centring spring can be adjusted, and whether the throttle stick can be set up to the feel you are used to.
Size, weight and power
Full-size radios with a large screen weigh around 600 g without a battery: the TX15 is 605 g and the TWIN X14 is 610 g. The DJI FPV Remote Controller 3 is about 240 g, with about 10 hours of operating time, and offers Normal, Sport and Manual modes.
Check what powers the radio and whether the battery is included. The TX15, for example, runs from a 2S LiPo or from 18650 or 21700 Li-ion cells, and the battery is not included.
If you also want to practise in a simulator, check that the radio works with the one you use. DJI lists Liftoff, Uncrashed, DCL and DRL for the FPV Remote Controller 3.
If you can, hold the radio before you buy it. Grip and switch placement make a difference over long sessions.
Checklist before you buy
Before you buy a radio:
- Its protocol matches the receivers in your drones, or the ones you plan to buy
- The module bay suits any extra protocol you might want later
- You are comfortable with its operating system, EdgeTX or ETHOS
- For flying in Israel, the control link is 2.4GHz - the band the Ministry of Communications approves for drones
- Hall-sensor gimbals
- You know which battery it takes and whether it is included



