Betaflight vs INAV vs ArduPilot: Which Firmware to Use
Betaflight, INAV and ArduPilot are all flight-controller firmware, but each was built for a different kind of flying. The right choice depends on what you want the drone to do, and it is best made before you buy the board, because switching later means starting your configuration again.
Which firmware for which drone?
Start from the flying you want to do, not from the firmware name. As a rule of thumb:
- I fly freestyle, racing or a cinewhoop by hand: Betaflight.
- I want a long-range quad with GPS, position hold and a return-home that I can set up myself: INAV.
- I fly a fixed wing with GPS return and waypoints: INAV, or ArduPilot Plane if you want a full autopilot.
- I want autonomous survey or mapping missions, geofencing or scripting: ArduPilot (or PX4).
- I am building a heavy-lift multirotor, a VTOL, a rover or a boat: ArduPilot.
- I only want something that flies and has a basic safety net if the link drops: Betaflight with GPS Rescue, or INAV.
Betaflight: built for flying by hand
Betaflight is aimed at multirotors flown manually. Its strengths are a very fast control loop, a flight feel that is easy to adjust, a rich on-screen display (OSD) and blackbox logging for tuning. It is the usual starting point for freestyle, racing and cinewhoop builds.
Flight modes are mostly about how you control the drone: acro (rate) mode, angle mode and horizon mode. If you add a GPS, GPS Rescue gives a basic return-home when the signal is lost. It is a safety net, not a navigation system: Betaflight does not fly waypoint missions or hold a position the way a full navigation firmware does.
You configure it with Betaflight Configurator. Tuning is mainly PID, filter and rate settings, and many pilots start from a preset and refine from there.
INAV: GPS navigation on a familiar base
INAV started from the same family of flight controllers as Betaflight, so its configurator and command-line interface will feel familiar. The difference is that navigation is a first-class feature: altitude hold, position hold, return-to-home and waypoint missions, for multirotors and for fixed wings.
That is why it is the common choice for long-range quads and for planes and flying wings that need GPS return. A mission is planned in the configurator or a compatible ground station and uploaded to the board before flight.
Navigation only works as well as its sensors. You need a GPS, in practice a compass for reliable multirotor navigation, and a barometer on the board for altitude-based modes. You also need the extra setup time: compass calibration, navigation settings and failsafe behaviour all have to be tested on the ground first. INAV Configurator is the setup tool.
ArduPilot (and PX4): a full autopilot
ArduPilot is a complete autopilot platform with separate vehicle firmware: Copter for multirotors, Plane for fixed wings, Rover for ground vehicles and boats, and Sub for underwater vehicles. It supports full autonomous missions, geofencing, VTOL plane configurations, scripting and a large range of sensors and peripherals.
It was developed on Pixhawk-class hardware, but it also supports a number of F4, F7 and H7 boards from drone manufacturers. Support is board by board, so never assume it: check that your exact board is listed (more on that below).
You set it up with Mission Planner or QGroundControl. Both are ground-control programs as well as setup tools, so you plan missions, watch live telemetry and change parameters in the same place. Expect more settings and a longer first setup than with Betaflight: a calibration and checking routine, then a careful first flight in a basic mode.
PX4 is the other major open-source autopilot. It targets a similar kind of work and is used with QGroundControl; if you are drawn to it, the same hardware-support checks apply.
How do I check that my board supports a firmware?
Firmware is built for a specific board, called a target. The target contains the pin assignments, sensors and UART layout of that exact design, so a build for a different board will misbehave even if the chip is the same.
Before buying, check four things:
- The firmware project's own list of supported boards has an entry for the exact board name, not just the same chip.
- The manufacturer says the board supports that firmware, and ideally links to a target or setup page.
- The flash size and sensors are enough: some older or smaller boards are left behind as firmware grows, and some have no barometer or compass input.
- If a target exists only as a beta or community build, treat it as less proven and read the notes first.
Flashing changes the whole configuration
You cannot try a firmware on a board and keep your settings. Betaflight, INAV and ArduPilot store their settings in different forms, with different names and different logic. After flashing, ports, receiver protocol, motor order and direction, modes, failsafe, OSD and tuning all need to be set up again.
Practical habits that save trouble:
- Save a full backup of the current configuration before flashing anything (for Betaflight and INAV, a dump from the CLI).
- Take the props off before flashing, and before the first power-up on a new firmware.
- Some boards need a different bootloader or a DFU-mode flash to move between firmwares. Follow the firmware's own page for that board.
- Write down which firmware and version a drone is running, so a spare board or a repair starts from the same point.
Hardware needs, effort and the honest learning curve
Count what the firmware needs, not just what the board offers. A GPS takes a UART, as do the receiver, a digital video system and any telemetry device. Navigation firmware adds a compass (often built into the GPS module) and wants a barometer on the board. ArduPilot setups often use more serial ports and an SD card for logging. If the board runs out of UARTs, something has to go.
On effort: Betaflight is the quickest to get flying and the most documented for the hobby, but good tuning still takes practice. INAV adds navigation setup and testing, and is a sensible step for a pilot who already knows Betaflight. ArduPilot has the steepest first-time learning curve and the widest capability, and it rewards patience and reading the documentation.
Whichever you choose, test failsafe and return-home behaviour in a safe open area before relying on it, and check the current local rules for the flying you plan to do. If you are still choosing between an FPV-style board and a dedicated autopilot, the guide on choosing a drone autopilot goes into more depth.



